American Water
American Water  
HomeAbout UsContact UsCareersInvestor RelationsCorporate ResponsibilityPress RoomLearning Center

Customer Service

About Us

Water Quality & Stewardship

Learning Center

Working With Us

Cross Connection and Backflow Prevention

Protecting your drinking water supply is also your responsibility!

What is a cross connection?
Cross Connection is a physical connection between a possible source of contamination and the public drinking water system piping. This connection, if not properly protected, can lead to the contamination of the drinking water system through a backflow event.

What is backflow?
Backflow is the reversal of water flow through a cross connection from a possible source of contamination into the public drinking water system. Backflow may be caused by either backpressure or backsiphonage. A loss of pressure in the public drinking water system may lead to backsiphonage through unprotected cross connections, or backpressure may be created when the water pressure of a facility’s internal water system is elevated above the supply pressure of the public drinking water system resulting in backflow through unprotected cross connections.

What can you do to prevent backflow situations in your home or business?
• Be aware of and eliminate and/or isolate cross connections.
• Maintain air gaps on sinks and when using hoses.
• Do not submerge hoses or place them where they could become submerged.
• Use hose bib vacuum breakers on fixtures (hose connections in the basement, laundry room, and on outside faucets/spigots).
• Install approved backflow prevention devices on lawn irrigation systems and on fire sprinkler system services.
• Do not create a connection between an auxiliary water system (well, cistern, body of water) and the water supply plumbing.

Who is responsible?
• The responsibility for preventing backflow is divided. In general, state and local plumbing inspectors have authority over plumbing systems within buildings while state regulatory agencies and public water suppliers regulate protection of the distribution system at each service connection.
• Water customers have the ultimate responsibility for properly maintaining their plumbing systems.
• It is the water customer’s responsibility to ensure that unprotected cross-connections are not created and that any required backflow prevention devices are tested in accordance with state requirements and maintained in operable condition.

Why should you be concerned?

• Backflow may affect the quality of the drinking water at your facility and has the potential to create health hazards if contaminated water enters your water supply plumbing system and is used for drinking, cooking or bathing.
• Backflow events occur more often than you might think although most do not create health hazards.
• Unprotected cross-connections with water supply plumbing or public drinking water piping systems are prohibited.
• You are responsible for protecting your water supply plumbing from backflow that may contaminate your drinking water and the drinking water of others. This includes complying with the plumbing code and not creating unprotected cross connections.

Who is responsible for having the backflow device tested?

• It is the responsibility of the property owner to have the backflow device tested by a qualified tester. It is also the responsibility of the property / business owner to schedule their own test appointment.

Who tests backflow devices?
While any Illinois licensed plumber can inspect plumbing or install a backflow device, only an Illinois Cross-Connection Control Device Inspector (CCCDI) can test the device.

Where can I find a list of qualified testers in my area?
• Illinois American Water does not endorse any specific testing company. Only hire plumbers with an Illinois
Cross-Connection Control Device Inspector (CCCDI) certification to test your backflow device.  Please check with Illinois American Water’s Cross Connection Department at 800-262-9440 if you have any questions.

I have an inground lawn sprinkler system at my residence. Am I required to have a backflow device and have it tested?
• Inground sprinkler systems are required to have a reduced pressure principle backflow prevention device installed on the water line servicing the system. The backflow device must also be periodically tested in accordance with the state testing requirements.

Who pays for the testing and how much does it cost?
• It is the responsibility of the property owner to pay for any testing and/or required repairs to the backflow device. Cost will vary with existing device location conditions and type of device. Please review pricing requirements with the selected test company/tester before having the test performed.

Will this cause any disruption in my water service?
• Testing does require the flow of water to be stopped through the backflow device during the test process resulting in a short service interruption. The testing can be scheduled through the test company/tester for a time that will be convenient for the property owner.

How often do I have to have my backflow device tested?
• Backflow devices are required to be tested upon installation and at annual intervals thereafter.

Do I submit the test to American Water or does the test company/tester do this for me?
• Usually the test company/tester submits the completed test form for their clients to the water company. If there is any doubt who will submit the test form, check with the test company/tester to verify who will be submitting the test form.

The test company/tester filled out their current test form to submit instead of Illinois American Water’s test form. Is this ok?
• Illinois American Water will gladly accept test forms other than our own as long as the backflow device information, testing information and customer information is complete and legible on the test form.

If I cannot get my device tested in time to meet the required deadline what should I do?
• Please call Illinois American Water’s Cross Connection Department at 800-262-9440 to discuss possible extensions and/or resolutions.

I received a cross connection survey on my water usage at my facility. What is this about?
• Illinois American Water conducts periodic surveys of their customers’ use of water to identify and eliminate possible sources of cross connections to help ensure the safety of the public water supply. The information collected through the surveys helps to identify where backflow prevention devices may be needed as well as providing information on existing devices that may not have been previously submitted to the water company.

How do I contact the ILAW Cross Connection Control Department?

• By phone:  (800) 262-9440

• By fax:  (618) 466-9422

• By email:  ilaw.crossconnection@amwater.com

• By mail:  ILAW Cross Connection Department, 4436 Industrial Drive, Alton, IL  62002

Resources

Illinois American Water Cross Connection Control Program Description
Residential Cross Connection Survey
Commercial Cross Connection Survey
Illinois American Water Test Form
Complete your Residential Cross Connection Control Water Survey Questionnaire online